View HR08D-12WPA-10S_9005019.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

sep.1.2018 copyright 2018 hirose electric co., ltd. all rights reserved. 1 2018.7 ? small, waterproof, push-on bayonet lock connectors hr08d series features 1. simplified mating operations ? to mate the connector, simply push it onto the receptacle. to unmate, rotate the locking collar and pull the plug back from the receptacle. (fig. q ) ? simplified mating is enabled by the alignment markings ? mating guide keys are provided at 3 points to prevent contact damage. they also provide the ability to blind mate these connectors when needed. plug connector does not damage the receptacle contacts. 2. waterproof structure supports ip67 and ip68 ratings while in the mated condition. (ratings explained below*) *ip67: submerged in 1 m for 30 minutes *ip68: submerged in 2 m for 14 days 3. adjustable cable direction the right angle plug can be adjusted to mount in any of the 8 different directions (adjustable in 45 increments). (fig. w ) 4. variations available fig. q fig. w items no. of contacts 2 or 10 positions available connector type straight plug, right angle plug, receptacle (10 pos. only) plug termination crimp, solder receptacle termination solder cord tube material plastic, metal cable diameter range (reference) 5.7 to 6.5 6.5 to 7.3 8.0 to 9.0 cable exit directions push-on bayonet lock mating is completed simply by pushing the plug onto the receptacle. to unmate this connector, rotate the locking collar to release the lock, then pull them apart. in cases where the application will demand a high level of reliability, such as automotive, please contact a company representative for further information. 2 hr08d series small, waterproof, push-on bayonet lock connectors product speci cations ratings rated current 3a operating temperature range -20? to +85? rated voltage ac200v, dc250v storage temperature range -10? to +60? items speci cations conditions 1. contact resistance 20m?or below measured with dc 1a 2.insulation resistance minimum of 1,000m measured with dc 500v 3. withstanding voltage no ashover or breakdown 10 pos. ac 900v for 1 minute 2 pos. ac 1,500v for 1 minute 4. vibration resistance no electrical discontinuity of 10? or greater tested in 3 directions with 10 to 500hz /cycle, total vibration width of 0.75mm, and 98m/s 2 , 3 hours each. 5. shock no electrical discontinuity of 10? or greater tested in 3 directions with the acceleration of 490m/s 2 , and a duration of 11ms, 3 times each 6. durability contact resistance : maximum of 30m 500 mating cycles 7. temperature cycles insulation resistance : minimum of 500m left at - 55? : 30 minutes e ordinary temperature : 2 to 3 minutes e 85? : 30 minutes e ordinary temperature : 2 to 3 minutes, 2 to 3 minutes, total of 5 cycles 8. humidity resistance insulation resistance minimum of 50m (high humidity) minimum of 500m (dry) left at temperature 71? and humidity 95% for 336 hours. left at the temperature of 71? and 95% humidity for 336 hours. 9. waterproof structure should be no water leakage inside the connector left submerged in water at the depth of 1m, for 0.5 hours, in the mated condition. materials / finish plug component materials finish remarks outer shell zinc alloy, aluminum alloy and polyamide resin (black) nickel under plating ---------------------- insulator pps resin (black) ---------------------- ul94v-0 female contact phosphorous bronze gold plating ---------------------- o ring, gasket nbr, nitrile hydride rubber ---------------------- ---------------------- receptacle component materials finish remarks outer shell zinc alloy nickel under plating ---------------------- insulator pps resin (black) ---------------------- ul94v-0 male contact 10 position brass gold plating ---------------------- o ring nbr ---------------------- ---------------------- product number structure refer to the chart below when determining the product specifications from the product number. please select from the product numbers listed in this catalog when placing orders. plug hr08d 12 wp a - 10 s ( ** ) ^ _ ` a b c d ^ model name : hr08d series _ shell size : diameter (mm) of the mating interface of the plug ` shell type wp : straight plug, wlp: right angle plug a cord tube and cable range type a : material of cord tube : metal, with cable dia. range of ( 5.7 to 6.5) b : material of cord tube : metal, with cable dia. range of ( 6.5 to 7.3) m : material of cord tube : plastic, with cable dia. range of ( 5.7 to 6.5) n : material of cord tube : plastic, with cable dia. range of ( 6.5 to 7.3) k : material of cord tube : metal, with cable dia. range of ( 8.0 to 9.0) b number of contacts : contacts available (2 or 10) c contact shape s : female contact for solder termination sc : female contact for crimping termination d other specifications : a two-digit character is added to indicate other specifications as needed. receptacle hr08d 12 wr - 10 p ( ** ) ^ _ ` a b c crimp contact hr34b - sc1 - 2 1 1 ^ _ ` a b ^ model name : hr08d series _ shell size : diameter (mm) of the mating interface of the plug ` shell type y wr receptacle a number of contacts : contacts available (10 only) b contact shape p : male contact for solder termination c other specifications : a two-digit character is added to indicate other specifications as needed. ^ model name : hr34b series (shares the same contacts as the hr34b series) _ contact type sc1 : female contact ` contact shape 1 : single contact 2 : reel contact a barrel shape : 1 : 20 to 25 awg b plating type 1 : gold plating 3 hr08d series small, waterproof, push-on bayonet lock connectors straight plug regular version ( cord tube material : plastic) robust version (cord tube material: metal) 8 10 47 13 20 a 49.1 (example) solder termination version part no. hrs no. a applicable cable diameter range (reference) contact solder cup inner diameter hr08d-12wpm-10s(31) 108-0274-5 31 7.4 5.7 to 6.5 1 hr08d-12wpn-10s(31) 108-0275-8 31 8.5 6.5 to 7.3 hr08d-12wpm-2s(31) 108-0272-0 31 7.4 5.7 to 6.5 1.8 hr08d-12wpn-2s(31) 108-0266-7 31 8.5 6.5 to 7.3 solder termination version part no. hrs no. a applicable cable diameter range (reference) contact solder cup inner diameter HR08D-12WPA-10S(31) 108-0219-7 31 7.4 5.7 to 6.5 1 hr08d-12wpb-10s(31) 108-0231-2 31 8.5 6.5 to 7.3 hr08d-12wpk-10s(31) 108-0262-6 31 9.5 8.0 to 9.0 hr08d-12wpa-2s(31) 108-0279-9 31 7.4 5.7 to 6.5 1.8 hr08d-12wpb-2s(31) 108-0280-8 31 8.5 6.5 to 7.3 hr08d-12wpk-2s(31) 108-0281-0 31 9.5 8.0 to 9.0 crimp termination version part no. hrs no. a applicable cable diameter range (reference) hr08d-12wpm-10sc(31) 108-0268-2 31 7.4 5.7 to 6.5 hr08d-12wpn-10sc(31) 108-0269-5 31 8.5 6.5 to 7.3 crimp termination version part no. hrs no. a applicable cable diameter range (reference) HR08D-12WPA-10Sc(31) 108-0220-6 31 7.4 5.7 to 6.5 hr08d-12wpb-10sc(31) 108-0232-5 31 8.5 6.5 to 7.3 hr08d-12wpk-10sc(31) 108-0263-9 31 9.5 8.0 to 9.0 4 hr08d series small, waterproof, push-on bayonet lock connectors right angle plug regular version ( cord tube material : plastic) robust version (cord tube material: metal) 10 8 7 4 13 20 33.5 ba ( exam p le ) solder termination version part no. hrs no. a b applicable cable diameter range (reference) contact solder cup inner diameter hr08d-12wlpm-10s(31) 108-0276-0 31 7.4 30.85 (5.7 to 6.5) 1 hr08d-12wlpn-10s(31) 108-0277-3 31 8.5 (6.5 to 7.3) hr08d-12wlpm-2s(31) 108-0273-2 31 7.4 (5.7 to 6.5) 1.8 hr08d-12wlpn-2s(31) 108-0267-0 31 8.5 (6.5 to 7.3) solder termination version part no. hrs no. a b applicable cable diameter range (reference) contact solder cup inner diameter hr08d-12wlpa-10s(31) 108-0221-9 31 7.4 30.5 (5.7 to 6.5) 1 hr08d-12wlpb-10s(31) 108-0233-8 31 8.5 (6.5 to 7.3) hr08d-12wlpk-10s(31) 108-0264-1 31 9.5 31.5 (8.0 to 9.0) hr08d-12wlpa-2s(31) 108-0282-3 31 7.4 30.5 (5.7 to 6.5) 1.8 hr08d-12wlpb-2s(31) 108-0283-6 31 8.5 (6.5 to 7.3) hr08d-12wlpk-2s(31) 108-0284-9 31 9.5 31.5 (8.0 to 9.0) crimp termination version part no. hrs no. a b applicable cable diameter range (reference) hr08d-12wlpm-10sc(31) 108-0270-4 31 7.4 30.85 (5.7 to 6.5) hr08d-12wlpn-10sc(31) 108-0271-7 31 8.5 (6.5 to 7.3) crimp termination version part no. hrs no. a b applicable cable diameter range (reference) hr08d-12wlpa-10sc(31) 108-0222-1 31 7.4 30.5 (5.7 to 6.5) hr08d-12wlpb-10sc(31) 108-0234-0 31 8.5 (6.5 to 7.3) hr08d-12wlpk-10sc(31) 108-0265-4 31 9.5 31.5 (8.0 to 9.0) 5 hr08d series small, waterproof, push-on bayonet lock connectors receptacle solder termination version b panel mount hole dimensions a b a b 4 (r2.8
4 3.2 a a c d e 4 part no. hrs no. a b contact solder cup inner diameter hr08d-12wr-10p(31) 108-0218-4 31 17.26 23.4 1.1 note : the number 10 contact is connected to the outer shell, which provides the ground connection. dimension hr08d-12wr-10p(31) a 17.26?.05 b m3?.5 c1 y 0/ ? 0.1 d 12.2 y +0.1/0 e 16.2 y +0.1/0 crimp contact female contact 1.2 15 type part no. hrs no. applicable electric wires loose piece contact hr34b-sc1-111 134-0051-7 20 to 25 awg reel contact hr34b-sc1-211 134-0050-4 note : the loose piece contacts are sold in packs of 100. reel contacts are sold in full reel quantities of 10,000 pieces per reel. 6 hr08d series small, waterproof, push-on bayonet lock connectors 2-6-3,nakagawa chuoh,tsuzuki-ku,yokohama-shi 224-8540,japan tel: + 81-45-620-3526 fax: + 81-45-591-3726 http://www.hirose.com http://www.hirose-connectors.com ? b applicable tools tools part no. hrs no. applicable contacts applicable wire size manual crimping tool ht304/hr34b-1 150-0107-9 hr34b-sc1-111 20 awg z 23 awg z 25 awg automatic crimping press cm-105c 901-0001-0 hr34b-sc1-211 20 to 25 awg automatic crimping applicator ap105-hr34b-1 901-2051-2 contact extraction tool rp6-sc-tp 150-0039-0 hr34b-sc1-111 hr34b-sc1-211 ---------------------- b manual crimping tool b operating precautions 1. prior to inserting or extracting this connector, make sure that the connector is not energized and the power is in the off posi tion. 2. there may be some resistance when inserting the cables into this connector, even if the cables are within the applicable cable range. this is to be expected due to the connector? waterproof ability. the waterproof performance and clamp force is dependant on t he cable specification. please check the cable specifications before using as they can cause a difference in performance in the waterpr oof protection and cable clamp force. 3. please contact your local hirose sales representative for any inquiries regarding the assembly procedures of this connector. b contact extraction tool b automatic crimping press cm-105c model (applicator sold separately) b plug contact diagram 2 position version 10 position version 1 2 321 7654 10 98 note : the numbering of the contact is from the plug termination side. the characteristics and the specifications contained herein are for reference purpose. please refer to the latest customer dra wings prior to use. the contents of this catalog are current as of date of 07/2018. contents are subject to change without notice for the purpose o f improvements.
sep.1.2018 copyright 2018 hirose electric co., ltd. all rights reserved. 1 2018.7 ? small, waterproof, push-on bayonet lock connectors hr08d series features 1. simplified mating operations ? to mate the connector, simply push it onto the receptacle. to unmate, rotate the locking collar and pull the plug back from the receptacle. (fig. q ) ? simplified mating is enabled by the alignment markings ? mating guide keys are provided at 3 points to prevent contact damage. they also provide the ability to blind mate these connectors when needed. plug connector does not damage the receptacle contacts. 2. waterproof structure supports ip67 and ip68 ratings while in the mated condition. (ratings explained below*) *ip67: submerged in 1 m for 30 minutes *ip68: submerged in 2 m for 14 days 3. adjustable cable direction the right angle plug can be adjusted to mount in any of the 8 different directions (adjustable in 45 increments). (fig. w ) 4. variations available fig. q fig. w items no. of contacts 2 or 10 positions available connector type straight plug, right angle plug, receptacle (10 pos. only) plug termination crimp, solder receptacle termination solder cord tube material plastic, metal cable diameter range (reference) 5.7 to 6.5 6.5 to 7.3 8.0 to 9.0 cable exit directions push-on bayonet lock mating is completed simply by pushing the plug onto the receptacle. to unmate this connector, rotate the locking collar to release the lock, then pull them apart. in cases where the application will demand a high level of reliability, such as automotive, please contact a company representative for further information. 2 hr08d series small, waterproof, push-on bayonet lock connectors product speci cations ratings rated current 3a operating temperature range -20? to +85? rated voltage ac200v, dc250v storage temperature range -10? to +60? items speci cations conditions 1. contact resistance 20m?or below measured with dc 1a 2.insulation resistance minimum of 1,000m measured with dc 500v 3. withstanding voltage no ashover or breakdown 10 pos. ac 900v for 1 minute 2 pos. ac 1,500v for 1 minute 4. vibration resistance no electrical discontinuity of 10? or greater tested in 3 directions with 10 to 500hz /cycle, total vibration width of 0.75mm, and 98m/s 2 , 3 hours each. 5. shock no electrical discontinuity of 10? or greater tested in 3 directions with the acceleration of 490m/s 2 , and a duration of 11ms, 3 times each 6. durability contact resistance : maximum of 30m 500 mating cycles 7. temperature cycles insulation resistance : minimum of 500m left at - 55? : 30 minutes e ordinary temperature : 2 to 3 minutes e 85? : 30 minutes e ordinary temperature : 2 to 3 minutes, 2 to 3 minutes, total of 5 cycles 8. humidity resistance insulation resistance minimum of 50m (high humidity) minimum of 500m (dry) left at temperature 71? and humidity 95% for 336 hours. left at the temperature of 71? and 95% humidity for 336 hours. 9. waterproof structure should be no water leakage inside the connector left submerged in water at the depth of 1m, for 0.5 hours, in the mated condition. materials / finish plug component materials finish remarks outer shell zinc alloy, aluminum alloy and polyamide resin (black) nickel under plating ---------------------- insulator pps resin (black) ---------------------- ul94v-0 female contact phosphorous bronze gold plating ---------------------- o ring, gasket nbr, nitrile hydride rubber ---------------------- ---------------------- receptacle component materials finish remarks outer shell zinc alloy nickel under plating ---------------------- insulator pps resin (black) ---------------------- ul94v-0 male contact 10 position brass gold plating ---------------------- o ring nbr ---------------------- ---------------------- product number structure refer to the chart below when determining the product specifications from the product number. please select from the product numbers listed in this catalog when placing orders. plug hr08d 12 wp a - 10 s ( ** ) ^ _ ` a b c d ^ model name : hr08d series _ shell size : diameter (mm) of the mating interface of the plug ` shell type wp : straight plug, wlp: right angle plug a cord tube and cable range type a : material of cord tube : metal, with cable dia. range of ( 5.7 to 6.5) b : material of cord tube : metal, with cable dia. range of ( 6.5 to 7.3) m : material of cord tube : plastic, with cable dia. range of ( 5.7 to 6.5) n : material of cord tube : plastic, with cable dia. range of ( 6.5 to 7.3) k : material of cord tube : metal, with cable dia. range of ( 8.0 to 9.0) b number of contacts : contacts available (2 or 10) c contact shape s : female contact for solder termination sc : female contact for crimping termination d other specifications : a two-digit character is added to indicate other specifications as needed. receptacle hr08d 12 wr - 10 p ( ** ) ^ _ ` a b c crimp contact hr34b - sc1 - 2 1 1 ^ _ ` a b ^ model name : hr08d series _ shell size : diameter (mm) of the mating interface of the plug ` shell type y wr receptacle a number of contacts : contacts available (10 only) b contact shape p : male contact for solder termination c other specifications : a two-digit character is added to indicate other specifications as needed. ^ model name : hr34b series (shares the same contacts as the hr34b series) _ contact type sc1 : female contact ` contact shape 1 : single contact 2 : reel contact a barrel shape : 1 : 20 to 25 awg b plating type 1 : gold plating 3 hr08d series small, waterproof, push-on bayonet lock connectors straight plug regular version ( cord tube material : plastic) robust version (cord tube material: metal) 8 10 47 13 20 a 49.1 (example) solder termination version part no. hrs no. a applicable cable diameter range (reference) contact solder cup inner diameter hr08d-12wpm-10s(31) 108-0274-5 31 7.4 5.7 to 6.5 1 hr08d-12wpn-10s(31) 108-0275-8 31 8.5 6.5 to 7.3 hr08d-12wpm-2s(31) 108-0272-0 31 7.4 5.7 to 6.5 1.8 hr08d-12wpn-2s(31) 108-0266-7 31 8.5 6.5 to 7.3 solder termination version part no. hrs no. a applicable cable diameter range (reference) contact solder cup inner diameter HR08D-12WPA-10S(31) 108-0219-7 31 7.4 5.7 to 6.5 1 hr08d-12wpb-10s(31) 108-0231-2 31 8.5 6.5 to 7.3 hr08d-12wpk-10s(31) 108-0262-6 31 9.5 8.0 to 9.0 hr08d-12wpa-2s(31) 108-0279-9 31 7.4 5.7 to 6.5 1.8 hr08d-12wpb-2s(31) 108-0280-8 31 8.5 6.5 to 7.3 hr08d-12wpk-2s(31) 108-0281-0 31 9.5 8.0 to 9.0 crimp termination version part no. hrs no. a applicable cable diameter range (reference) hr08d-12wpm-10sc(31) 108-0268-2 31 7.4 5.7 to 6.5 hr08d-12wpn-10sc(31) 108-0269-5 31 8.5 6.5 to 7.3 crimp termination version part no. hrs no. a applicable cable diameter range (reference) HR08D-12WPA-10Sc(31) 108-0220-6 31 7.4 5.7 to 6.5 hr08d-12wpb-10sc(31) 108-0232-5 31 8.5 6.5 to 7.3 hr08d-12wpk-10sc(31) 108-0263-9 31 9.5 8.0 to 9.0 4 hr08d series small, waterproof, push-on bayonet lock connectors right angle plug regular version ( cord tube material : plastic) robust version (cord tube material: metal) 10 8 7 4 13 20 33.5 ba ( exam p le ) solder termination version part no. hrs no. a b applicable cable diameter range (reference) contact solder cup inner diameter hr08d-12wlpm-10s(31) 108-0276-0 31 7.4 30.85 (5.7 to 6.5) 1 hr08d-12wlpn-10s(31) 108-0277-3 31 8.5 (6.5 to 7.3) hr08d-12wlpm-2s(31) 108-0273-2 31 7.4 (5.7 to 6.5) 1.8 hr08d-12wlpn-2s(31) 108-0267-0 31 8.5 (6.5 to 7.3) solder termination version part no. hrs no. a b applicable cable diameter range (reference) contact solder cup inner diameter hr08d-12wlpa-10s(31) 108-0221-9 31 7.4 30.5 (5.7 to 6.5) 1 hr08d-12wlpb-10s(31) 108-0233-8 31 8.5 (6.5 to 7.3) hr08d-12wlpk-10s(31) 108-0264-1 31 9.5 31.5 (8.0 to 9.0) hr08d-12wlpa-2s(31) 108-0282-3 31 7.4 30.5 (5.7 to 6.5) 1.8 hr08d-12wlpb-2s(31) 108-0283-6 31 8.5 (6.5 to 7.3) hr08d-12wlpk-2s(31) 108-0284-9 31 9.5 31.5 (8.0 to 9.0) crimp termination version part no. hrs no. a b applicable cable diameter range (reference) hr08d-12wlpm-10sc(31) 108-0270-4 31 7.4 30.85 (5.7 to 6.5) hr08d-12wlpn-10sc(31) 108-0271-7 31 8.5 (6.5 to 7.3) crimp termination version part no. hrs no. a b applicable cable diameter range (reference) hr08d-12wlpa-10sc(31) 108-0222-1 31 7.4 30.5 (5.7 to 6.5) hr08d-12wlpb-10sc(31) 108-0234-0 31 8.5 (6.5 to 7.3) hr08d-12wlpk-10sc(31) 108-0265-4 31 9.5 31.5 (8.0 to 9.0) 5 hr08d series small, waterproof, push-on bayonet lock connectors receptacle solder termination version b panel mount hole dimensions a b a b 4 (r2.8
4 3.2 a a c d e 4 part no. hrs no. a b contact solder cup inner diameter hr08d-12wr-10p(31) 108-0218-4 31 17.26 23.4 1.1 note : the number 10 contact is connected to the outer shell, which provides the ground connection. dimension hr08d-12wr-10p(31) a 17.26?.05 b m3?.5 c1 y 0/ ? 0.1 d 12.2 y +0.1/0 e 16.2 y +0.1/0 crimp contact female contact 1.2 15 type part no. hrs no. applicable electric wires loose piece contact hr34b-sc1-111 134-0051-7 20 to 25 awg reel contact hr34b-sc1-211 134-0050-4 note : the loose piece contacts are sold in packs of 100. reel contacts are sold in full reel quantities of 10,000 pieces per reel. 6 hr08d series small, waterproof, push-on bayonet lock connectors 2-6-3,nakagawa chuoh,tsuzuki-ku,yokohama-shi 224-8540,japan tel: + 81-45-620-3526 fax: + 81-45-591-3726 http://www.hirose.com http://www.hirose-connectors.com ? b applicable tools tools part no. hrs no. applicable contacts applicable wire size manual crimping tool ht304/hr34b-1 150-0107-9 hr34b-sc1-111 20 awg z 23 awg z 25 awg automatic crimping press cm-105c 901-0001-0 hr34b-sc1-211 20 to 25 awg automatic crimping applicator ap105-hr34b-1 901-2051-2 contact extraction tool rp6-sc-tp 150-0039-0 hr34b-sc1-111 hr34b-sc1-211 ---------------------- b manual crimping tool b operating precautions 1. prior to inserting or extracting this connector, make sure that the connector is not energized and the power is in the off posi tion. 2. there may be some resistance when inserting the cables into this connector, even if the cables are within the applicable cable range. this is to be expected due to the connector? waterproof ability. the waterproof performance and clamp force is dependant on t he cable specification. please check the cable specifications before using as they can cause a difference in performance in the waterpr oof protection and cable clamp force. 3. please contact your local hirose sales representative for any inquiries regarding the assembly procedures of this connector. b contact extraction tool b automatic crimping press cm-105c model (applicator sold separately) b plug contact diagram 2 position version 10 position version 1 2 321 7654 10 98 note : the numbering of the contact is from the plug termination side. the characteristics and the specifications contained herein are for reference purpose. please refer to the latest customer dra wings prior to use. the contents of this catalog are current as of date of 07/2018. contents are subject to change without notice for the purpose o f improvements.
sep.1.2018 copyright 2018 hirose electric co., ltd. all rights reserved. 1 2018.7 ? small, waterproof, push-on bayonet lock connectors hr08d series features 1. simplified mating operations ? to mate the connector, simply push it onto the receptacle. to unmate, rotate the locking collar and pull the plug back from the receptacle. (fig. q ) ? simplified mating is enabled by the alignment markings ? mating guide keys are provided at 3 points to prevent contact damage. they also provide the ability to blind mate these connectors when needed. plug connector does not damage the receptacle contacts. 2. waterproof structure supports ip67 and ip68 ratings while in the mated condition. (ratings explained below*) *ip67: submerged in 1 m for 30 minutes *ip68: submerged in 2 m for 14 days 3. adjustable cable direction the right angle plug can be adjusted to mount in any of the 8 different directions (adjustable in 45 increments). (fig. w ) 4. variations available fig. q fig. w items no. of contacts 2 or 10 positions available connector type straight plug, right angle plug, receptacle (10 pos. only) plug termination crimp, solder receptacle termination solder cord tube material plastic, metal cable diameter range (reference) 5.7 to 6.5 6.5 to 7.3 8.0 to 9.0 cable exit directions push-on bayonet lock mating is completed simply by pushing the plug onto the receptacle. to unmate this connector, rotate the locking collar to release the lock, then pull them apart. in cases where the application will demand a high level of reliability, such as automotive, please contact a company representative for further information. 2 hr08d series small, waterproof, push-on bayonet lock connectors product speci cations ratings rated current 3a operating temperature range -20? to +85? rated voltage ac200v, dc250v storage temperature range -10? to +60? items speci cations conditions 1. contact resistance 20m?or below measured with dc 1a 2.insulation resistance minimum of 1,000m measured with dc 500v 3. withstanding voltage no ashover or breakdown 10 pos. ac 900v for 1 minute 2 pos. ac 1,500v for 1 minute 4. vibration resistance no electrical discontinuity of 10? or greater tested in 3 directions with 10 to 500hz /cycle, total vibration width of 0.75mm, and 98m/s 2 , 3 hours each. 5. shock no electrical discontinuity of 10? or greater tested in 3 directions with the acceleration of 490m/s 2 , and a duration of 11ms, 3 times each 6. durability contact resistance : maximum of 30m 500 mating cycles 7. temperature cycles insulation resistance : minimum of 500m left at - 55? : 30 minutes e ordinary temperature : 2 to 3 minutes e 85? : 30 minutes e ordinary temperature : 2 to 3 minutes, 2 to 3 minutes, total of 5 cycles 8. humidity resistance insulation resistance minimum of 50m (high humidity) minimum of 500m (dry) left at temperature 71? and humidity 95% for 336 hours. left at the temperature of 71? and 95% humidity for 336 hours. 9. waterproof structure should be no water leakage inside the connector left submerged in water at the depth of 1m, for 0.5 hours, in the mated condition. materials / finish plug component materials finish remarks outer shell zinc alloy, aluminum alloy and polyamide resin (black) nickel under plating ---------------------- insulator pps resin (black) ---------------------- ul94v-0 female contact phosphorous bronze gold plating ---------------------- o ring, gasket nbr, nitrile hydride rubber ---------------------- ---------------------- receptacle component materials finish remarks outer shell zinc alloy nickel under plating ---------------------- insulator pps resin (black) ---------------------- ul94v-0 male contact 10 position brass gold plating ---------------------- o ring nbr ---------------------- ---------------------- product number structure refer to the chart below when determining the product specifications from the product number. please select from the product numbers listed in this catalog when placing orders. plug hr08d 12 wp a - 10 s ( ** ) ^ _ ` a b c d ^ model name : hr08d series _ shell size : diameter (mm) of the mating interface of the plug ` shell type wp : straight plug, wlp: right angle plug a cord tube and cable range type a : material of cord tube : metal, with cable dia. range of ( 5.7 to 6.5) b : material of cord tube : metal, with cable dia. range of ( 6.5 to 7.3) m : material of cord tube : plastic, with cable dia. range of ( 5.7 to 6.5) n : material of cord tube : plastic, with cable dia. range of ( 6.5 to 7.3) k : material of cord tube : metal, with cable dia. range of ( 8.0 to 9.0) b number of contacts : contacts available (2 or 10) c contact shape s : female contact for solder termination sc : female contact for crimping termination d other specifications : a two-digit character is added to indicate other specifications as needed. receptacle hr08d 12 wr - 10 p ( ** ) ^ _ ` a b c crimp contact hr34b - sc1 - 2 1 1 ^ _ ` a b ^ model name : hr08d series _ shell size : diameter (mm) of the mating interface of the plug ` shell type y wr receptacle a number of contacts : contacts available (10 only) b contact shape p : male contact for solder termination c other specifications : a two-digit character is added to indicate other specifications as needed. ^ model name : hr34b series (shares the same contacts as the hr34b series) _ contact type sc1 : female contact ` contact shape 1 : single contact 2 : reel contact a barrel shape : 1 : 20 to 25 awg b plating type 1 : gold plating 3 hr08d series small, waterproof, push-on bayonet lock connectors straight plug regular version ( cord tube material : plastic) robust version (cord tube material: metal) 8 10 47 13 20 a 49.1 (example) solder termination version part no. hrs no. a applicable cable diameter range (reference) contact solder cup inner diameter hr08d-12wpm-10s(31) 108-0274-5 31 7.4 5.7 to 6.5 1 hr08d-12wpn-10s(31) 108-0275-8 31 8.5 6.5 to 7.3 hr08d-12wpm-2s(31) 108-0272-0 31 7.4 5.7 to 6.5 1.8 hr08d-12wpn-2s(31) 108-0266-7 31 8.5 6.5 to 7.3 solder termination version part no. hrs no. a applicable cable diameter range (reference) contact solder cup inner diameter HR08D-12WPA-10S(31) 108-0219-7 31 7.4 5.7 to 6.5 1 hr08d-12wpb-10s(31) 108-0231-2 31 8.5 6.5 to 7.3 hr08d-12wpk-10s(31) 108-0262-6 31 9.5 8.0 to 9.0 hr08d-12wpa-2s(31) 108-0279-9 31 7.4 5.7 to 6.5 1.8 hr08d-12wpb-2s(31) 108-0280-8 31 8.5 6.5 to 7.3 hr08d-12wpk-2s(31) 108-0281-0 31 9.5 8.0 to 9.0 crimp termination version part no. hrs no. a applicable cable diameter range (reference) hr08d-12wpm-10sc(31) 108-0268-2 31 7.4 5.7 to 6.5 hr08d-12wpn-10sc(31) 108-0269-5 31 8.5 6.5 to 7.3 crimp termination version part no. hrs no. a applicable cable diameter range (reference) HR08D-12WPA-10Sc(31) 108-0220-6 31 7.4 5.7 to 6.5 hr08d-12wpb-10sc(31) 108-0232-5 31 8.5 6.5 to 7.3 hr08d-12wpk-10sc(31) 108-0263-9 31 9.5 8.0 to 9.0 4 hr08d series small, waterproof, push-on bayonet lock connectors right angle plug regular version ( cord tube material : plastic) robust version (cord tube material: metal) 10 8 7 4 13 20 33.5 ba ( exam p le ) solder termination version part no. hrs no. a b applicable cable diameter range (reference) contact solder cup inner diameter hr08d-12wlpm-10s(31) 108-0276-0 31 7.4 30.85 (5.7 to 6.5) 1 hr08d-12wlpn-10s(31) 108-0277-3 31 8.5 (6.5 to 7.3) hr08d-12wlpm-2s(31) 108-0273-2 31 7.4 (5.7 to 6.5) 1.8 hr08d-12wlpn-2s(31) 108-0267-0 31 8.5 (6.5 to 7.3) solder termination version part no. hrs no. a b applicable cable diameter range (reference) contact solder cup inner diameter hr08d-12wlpa-10s(31) 108-0221-9 31 7.4 30.5 (5.7 to 6.5) 1 hr08d-12wlpb-10s(31) 108-0233-8 31 8.5 (6.5 to 7.3) hr08d-12wlpk-10s(31) 108-0264-1 31 9.5 31.5 (8.0 to 9.0) hr08d-12wlpa-2s(31) 108-0282-3 31 7.4 30.5 (5.7 to 6.5) 1.8 hr08d-12wlpb-2s(31) 108-0283-6 31 8.5 (6.5 to 7.3) hr08d-12wlpk-2s(31) 108-0284-9 31 9.5 31.5 (8.0 to 9.0) crimp termination version part no. hrs no. a b applicable cable diameter range (reference) hr08d-12wlpm-10sc(31) 108-0270-4 31 7.4 30.85 (5.7 to 6.5) hr08d-12wlpn-10sc(31) 108-0271-7 31 8.5 (6.5 to 7.3) crimp termination version part no. hrs no. a b applicable cable diameter range (reference) hr08d-12wlpa-10sc(31) 108-0222-1 31 7.4 30.5 (5.7 to 6.5) hr08d-12wlpb-10sc(31) 108-0234-0 31 8.5 (6.5 to 7.3) hr08d-12wlpk-10sc(31) 108-0265-4 31 9.5 31.5 (8.0 to 9.0) 5 hr08d series small, waterproof, push-on bayonet lock connectors receptacle solder termination version b panel mount hole dimensions a b a b 4 (r2.8
4 3.2 a a c d e 4 part no. hrs no. a b contact solder cup inner diameter hr08d-12wr-10p(31) 108-0218-4 31 17.26 23.4 1.1 note : the number 10 contact is connected to the outer shell, which provides the ground connection. dimension hr08d-12wr-10p(31) a 17.26?.05 b m3?.5 c1 y 0/ ? 0.1 d 12.2 y +0.1/0 e 16.2 y +0.1/0 crimp contact female contact 1.2 15 type part no. hrs no. applicable electric wires loose piece contact hr34b-sc1-111 134-0051-7 20 to 25 awg reel contact hr34b-sc1-211 134-0050-4 note : the loose piece contacts are sold in packs of 100. reel contacts are sold in full reel quantities of 10,000 pieces per reel. 6 hr08d series small, waterproof, push-on bayonet lock connectors 2-6-3,nakagawa chuoh,tsuzuki-ku,yokohama-shi 224-8540,japan tel: + 81-45-620-3526 fax: + 81-45-591-3726 http://www.hirose.com http://www.hirose-connectors.com ? b applicable tools tools part no. hrs no. applicable contacts applicable wire size manual crimping tool ht304/hr34b-1 150-0107-9 hr34b-sc1-111 20 awg z 23 awg z 25 awg automatic crimping press cm-105c 901-0001-0 hr34b-sc1-211 20 to 25 awg automatic crimping applicator ap105-hr34b-1 901-2051-2 contact extraction tool rp6-sc-tp 150-0039-0 hr34b-sc1-111 hr34b-sc1-211 ---------------------- b manual crimping tool b operating precautions 1. prior to inserting or extracting this connector, make sure that the connector is not energized and the power is in the off posi tion. 2. there may be some resistance when inserting the cables into this connector, even if the cables are within the applicable cable range. this is to be expected due to the connector? waterproof ability. the waterproof performance and clamp force is dependant on t he cable specification. please check the cable specifications before using as they can cause a difference in performance in the waterpr oof protection and cable clamp force. 3. please contact your local hirose sales representative for any inquiries regarding the assembly procedures of this connector. b contact extraction tool b automatic crimping press cm-105c model (applicator sold separately) b plug contact diagram 2 position version 10 position version 1 2 321 7654 10 98 note : the numbering of the contact is from the plug termination side. the characteristics and the specifications contained herein are for reference purpose. please refer to the latest customer dra wings prior to use. the contents of this catalog are current as of date of 07/2018. contents are subject to change without notice for the purpose o f improvements.
sep.1.2018 copyright 2018 hirose electric co., ltd. all rights reserved. 1 2018.7 ? small, waterproof, push-on bayonet lock connectors hr08d series features 1. simplified mating operations ? to mate the connector, simply push it onto the receptacle. to unmate, rotate the locking collar and pull the plug back from the receptacle. (fig. q ) ? simplified mating is enabled by the alignment markings ? mating guide keys are provided at 3 points to prevent contact damage. they also provide the ability to blind mate these connectors when needed. plug connector does not damage the receptacle contacts. 2. waterproof structure supports ip67 and ip68 ratings while in the mated condition. (ratings explained below*) *ip67: submerged in 1 m for 30 minutes *ip68: submerged in 2 m for 14 days 3. adjustable cable direction the right angle plug can be adjusted to mount in any of the 8 different directions (adjustable in 45 increments). (fig. w ) 4. variations available fig. q fig. w items no. of contacts 2 or 10 positions available connector type straight plug, right angle plug, receptacle (10 pos. only) plug termination crimp, solder receptacle termination solder cord tube material plastic, metal cable diameter range (reference) 5.7 to 6.5 6.5 to 7.3 8.0 to 9.0 cable exit directions push-on bayonet lock mating is completed simply by pushing the plug onto the receptacle. to unmate this connector, rotate the locking collar to release the lock, then pull them apart. in cases where the application will demand a high level of reliability, such as automotive, please contact a company representative for further information. 2 hr08d series small, waterproof, push-on bayonet lock connectors product speci cations ratings rated current 3a operating temperature range -20? to +85? rated voltage ac200v, dc250v storage temperature range -10? to +60? items speci cations conditions 1. contact resistance 20m?or below measured with dc 1a 2.insulation resistance minimum of 1,000m measured with dc 500v 3. withstanding voltage no ashover or breakdown 10 pos. ac 900v for 1 minute 2 pos. ac 1,500v for 1 minute 4. vibration resistance no electrical discontinuity of 10? or greater tested in 3 directions with 10 to 500hz /cycle, total vibration width of 0.75mm, and 98m/s 2 , 3 hours each. 5. shock no electrical discontinuity of 10? or greater tested in 3 directions with the acceleration of 490m/s 2 , and a duration of 11ms, 3 times each 6. durability contact resistance : maximum of 30m 500 mating cycles 7. temperature cycles insulation resistance : minimum of 500m left at - 55? : 30 minutes e ordinary temperature : 2 to 3 minutes e 85? : 30 minutes e ordinary temperature : 2 to 3 minutes, 2 to 3 minutes, total of 5 cycles 8. humidity resistance insulation resistance minimum of 50m (high humidity) minimum of 500m (dry) left at temperature 71? and humidity 95% for 336 hours. left at the temperature of 71? and 95% humidity for 336 hours. 9. waterproof structure should be no water leakage inside the connector left submerged in water at the depth of 1m, for 0.5 hours, in the mated condition. materials / finish plug component materials finish remarks outer shell zinc alloy, aluminum alloy and polyamide resin (black) nickel under plating ---------------------- insulator pps resin (black) ---------------------- ul94v-0 female contact phosphorous bronze gold plating ---------------------- o ring, gasket nbr, nitrile hydride rubber ---------------------- ---------------------- receptacle component materials finish remarks outer shell zinc alloy nickel under plating ---------------------- insulator pps resin (black) ---------------------- ul94v-0 male contact 10 position brass gold plating ---------------------- o ring nbr ---------------------- ---------------------- product number structure refer to the chart below when determining the product specifications from the product number. please select from the product numbers listed in this catalog when placing orders. plug hr08d 12 wp a - 10 s ( ** ) ^ _ ` a b c d ^ model name : hr08d series _ shell size : diameter (mm) of the mating interface of the plug ` shell type wp : straight plug, wlp: right angle plug a cord tube and cable range type a : material of cord tube : metal, with cable dia. range of ( 5.7 to 6.5) b : material of cord tube : metal, with cable dia. range of ( 6.5 to 7.3) m : material of cord tube : plastic, with cable dia. range of ( 5.7 to 6.5) n : material of cord tube : plastic, with cable dia. range of ( 6.5 to 7.3) k : material of cord tube : metal, with cable dia. range of ( 8.0 to 9.0) b number of contacts : contacts available (2 or 10) c contact shape s : female contact for solder termination sc : female contact for crimping termination d other specifications : a two-digit character is added to indicate other specifications as needed. receptacle hr08d 12 wr - 10 p ( ** ) ^ _ ` a b c crimp contact hr34b - sc1 - 2 1 1 ^ _ ` a b ^ model name : hr08d series _ shell size : diameter (mm) of the mating interface of the plug ` shell type y wr receptacle a number of contacts : contacts available (10 only) b contact shape p : male contact for solder termination c other specifications : a two-digit character is added to indicate other specifications as needed. ^ model name : hr34b series (shares the same contacts as the hr34b series) _ contact type sc1 : female contact ` contact shape 1 : single contact 2 : reel contact a barrel shape : 1 : 20 to 25 awg b plating type 1 : gold plating 3 hr08d series small, waterproof, push-on bayonet lock connectors straight plug regular version ( cord tube material : plastic) robust version (cord tube material: metal) 8 10 47 13 20 a 49.1 (example) solder termination version part no. hrs no. a applicable cable diameter range (reference) contact solder cup inner diameter hr08d-12wpm-10s(31) 108-0274-5 31 7.4 5.7 to 6.5 1 hr08d-12wpn-10s(31) 108-0275-8 31 8.5 6.5 to 7.3 hr08d-12wpm-2s(31) 108-0272-0 31 7.4 5.7 to 6.5 1.8 hr08d-12wpn-2s(31) 108-0266-7 31 8.5 6.5 to 7.3 solder termination version part no. hrs no. a applicable cable diameter range (reference) contact solder cup inner diameter HR08D-12WPA-10S(31) 108-0219-7 31 7.4 5.7 to 6.5 1 hr08d-12wpb-10s(31) 108-0231-2 31 8.5 6.5 to 7.3 hr08d-12wpk-10s(31) 108-0262-6 31 9.5 8.0 to 9.0 hr08d-12wpa-2s(31) 108-0279-9 31 7.4 5.7 to 6.5 1.8 hr08d-12wpb-2s(31) 108-0280-8 31 8.5 6.5 to 7.3 hr08d-12wpk-2s(31) 108-0281-0 31 9.5 8.0 to 9.0 crimp termination version part no. hrs no. a applicable cable diameter range (reference) hr08d-12wpm-10sc(31) 108-0268-2 31 7.4 5.7 to 6.5 hr08d-12wpn-10sc(31) 108-0269-5 31 8.5 6.5 to 7.3 crimp termination version part no. hrs no. a applicable cable diameter range (reference) HR08D-12WPA-10Sc(31) 108-0220-6 31 7.4 5.7 to 6.5 hr08d-12wpb-10sc(31) 108-0232-5 31 8.5 6.5 to 7.3 hr08d-12wpk-10sc(31) 108-0263-9 31 9.5 8.0 to 9.0 4 hr08d series small, waterproof, push-on bayonet lock connectors right angle plug regular version ( cord tube material : plastic) robust version (cord tube material: metal) 10 8 7 4 13 20 33.5 ba ( exam p le ) solder termination version part no. hrs no. a b applicable cable diameter range (reference) contact solder cup inner diameter hr08d-12wlpm-10s(31) 108-0276-0 31 7.4 30.85 (5.7 to 6.5) 1 hr08d-12wlpn-10s(31) 108-0277-3 31 8.5 (6.5 to 7.3) hr08d-12wlpm-2s(31) 108-0273-2 31 7.4 (5.7 to 6.5) 1.8 hr08d-12wlpn-2s(31) 108-0267-0 31 8.5 (6.5 to 7.3) solder termination version part no. hrs no. a b applicable cable diameter range (reference) contact solder cup inner diameter hr08d-12wlpa-10s(31) 108-0221-9 31 7.4 30.5 (5.7 to 6.5) 1 hr08d-12wlpb-10s(31) 108-0233-8 31 8.5 (6.5 to 7.3) hr08d-12wlpk-10s(31) 108-0264-1 31 9.5 31.5 (8.0 to 9.0) hr08d-12wlpa-2s(31) 108-0282-3 31 7.4 30.5 (5.7 to 6.5) 1.8 hr08d-12wlpb-2s(31) 108-0283-6 31 8.5 (6.5 to 7.3) hr08d-12wlpk-2s(31) 108-0284-9 31 9.5 31.5 (8.0 to 9.0) crimp termination version part no. hrs no. a b applicable cable diameter range (reference) hr08d-12wlpm-10sc(31) 108-0270-4 31 7.4 30.85 (5.7 to 6.5) hr08d-12wlpn-10sc(31) 108-0271-7 31 8.5 (6.5 to 7.3) crimp termination version part no. hrs no. a b applicable cable diameter range (reference) hr08d-12wlpa-10sc(31) 108-0222-1 31 7.4 30.5 (5.7 to 6.5) hr08d-12wlpb-10sc(31) 108-0234-0 31 8.5 (6.5 to 7.3) hr08d-12wlpk-10sc(31) 108-0265-4 31 9.5 31.5 (8.0 to 9.0) 5 hr08d series small, waterproof, push-on bayonet lock connectors receptacle solder termination version b panel mount hole dimensions a b a b 4 (r2.8
4 3.2 a a c d e 4 part no. hrs no. a b contact solder cup inner diameter hr08d-12wr-10p(31) 108-0218-4 31 17.26 23.4 1.1 note : the number 10 contact is connected to the outer shell, which provides the ground connection. dimension hr08d-12wr-10p(31) a 17.26?.05 b m3?.5 c1 y 0/ ? 0.1 d 12.2 y +0.1/0 e 16.2 y +0.1/0 crimp contact female contact 1.2 15 type part no. hrs no. applicable electric wires loose piece contact hr34b-sc1-111 134-0051-7 20 to 25 awg reel contact hr34b-sc1-211 134-0050-4 note : the loose piece contacts are sold in packs of 100. reel contacts are sold in full reel quantities of 10,000 pieces per reel. 6 hr08d series small, waterproof, push-on bayonet lock connectors 2-6-3,nakagawa chuoh,tsuzuki-ku,yokohama-shi 224-8540,japan tel: + 81-45-620-3526 fax: + 81-45-591-3726 http://www.hirose.com http://www.hirose-connectors.com ? b applicable tools tools part no. hrs no. applicable contacts applicable wire size manual crimping tool ht304/hr34b-1 150-0107-9 hr34b-sc1-111 20 awg z 23 awg z 25 awg automatic crimping press cm-105c 901-0001-0 hr34b-sc1-211 20 to 25 awg automatic crimping applicator ap105-hr34b-1 901-2051-2 contact extraction tool rp6-sc-tp 150-0039-0 hr34b-sc1-111 hr34b-sc1-211 ---------------------- b manual crimping tool b operating precautions 1. prior to inserting or extracting this connector, make sure that the connector is not energized and the power is in the off posi tion. 2. there may be some resistance when inserting the cables into this connector, even if the cables are within the applicable cable range. this is to be expected due to the connector? waterproof ability. the waterproof performance and clamp force is dependant on t he cable specification. please check the cable specifications before using as they can cause a difference in performance in the waterpr oof protection and cable clamp force. 3. please contact your local hirose sales representative for any inquiries regarding the assembly procedures of this connector. b contact extraction tool b automatic crimping press cm-105c model (applicator sold separately) b plug contact diagram 2 position version 10 position version 1 2 321 7654 10 98 note : the numbering of the contact is from the plug termination side. the characteristics and the specifications contained herein are for reference purpose. please refer to the latest customer dra wings prior to use. the contents of this catalog are current as of date of 07/2018. contents are subject to change without notice for the purpose o f improvements.
sep.1.2018 copyright 2018 hirose electric co., ltd. all rights reserved. 1 2018.7 ? small, waterproof, push-on bayonet lock connectors hr08d series features 1. simplified mating operations ? to mate the connector, simply push it onto the receptacle. to unmate, rotate the locking collar and pull the plug back from the receptacle. (fig. q ) ? simplified mating is enabled by the alignment markings ? mating guide keys are provided at 3 points to prevent contact damage. they also provide the ability to blind mate these connectors when needed. plug connector does not damage the receptacle contacts. 2. waterproof structure supports ip67 and ip68 ratings while in the mated condition. (ratings explained below*) *ip67: submerged in 1 m for 30 minutes *ip68: submerged in 2 m for 14 days 3. adjustable cable direction the right angle plug can be adjusted to mount in any of the 8 different directions (adjustable in 45 increments). (fig. w ) 4. variations available fig. q fig. w items no. of contacts 2 or 10 positions available connector type straight plug, right angle plug, receptacle (10 pos. only) plug termination crimp, solder receptacle termination solder cord tube material plastic, metal cable diameter range (reference) 5.7 to 6.5 6.5 to 7.3 8.0 to 9.0 cable exit directions push-on bayonet lock mating is completed simply by pushing the plug onto the receptacle. to unmate this connector, rotate the locking collar to release the lock, then pull them apart. in cases where the application will demand a high level of reliability, such as automotive, please contact a company representative for further information. 2 hr08d series small, waterproof, push-on bayonet lock connectors product speci cations ratings rated current 3a operating temperature range -20? to +85? rated voltage ac200v, dc250v storage temperature range -10? to +60? items speci cations conditions 1. contact resistance 20m?or below measured with dc 1a 2.insulation resistance minimum of 1,000m measured with dc 500v 3. withstanding voltage no ashover or breakdown 10 pos. ac 900v for 1 minute 2 pos. ac 1,500v for 1 minute 4. vibration resistance no electrical discontinuity of 10? or greater tested in 3 directions with 10 to 500hz /cycle, total vibration width of 0.75mm, and 98m/s 2 , 3 hours each. 5. shock no electrical discontinuity of 10? or greater tested in 3 directions with the acceleration of 490m/s 2 , and a duration of 11ms, 3 times each 6. durability contact resistance : maximum of 30m 500 mating cycles 7. temperature cycles insulation resistance : minimum of 500m left at - 55? : 30 minutes e ordinary temperature : 2 to 3 minutes e 85? : 30 minutes e ordinary temperature : 2 to 3 minutes, 2 to 3 minutes, total of 5 cycles 8. humidity resistance insulation resistance minimum of 50m (high humidity) minimum of 500m (dry) left at temperature 71? and humidity 95% for 336 hours. left at the temperature of 71? and 95% humidity for 336 hours. 9. waterproof structure should be no water leakage inside the connector left submerged in water at the depth of 1m, for 0.5 hours, in the mated condition. materials / finish plug component materials finish remarks outer shell zinc alloy, aluminum alloy and polyamide resin (black) nickel under plating ---------------------- insulator pps resin (black) ---------------------- ul94v-0 female contact phosphorous bronze gold plating ---------------------- o ring, gasket nbr, nitrile hydride rubber ---------------------- ---------------------- receptacle component materials finish remarks outer shell zinc alloy nickel under plating ---------------------- insulator pps resin (black) ---------------------- ul94v-0 male contact 10 position brass gold plating ---------------------- o ring nbr ---------------------- ---------------------- product number structure refer to the chart below when determining the product specifications from the product number. please select from the product numbers listed in this catalog when placing orders. plug hr08d 12 wp a - 10 s ( ** ) ^ _ ` a b c d ^ model name : hr08d series _ shell size : diameter (mm) of the mating interface of the plug ` shell type wp : straight plug, wlp: right angle plug a cord tube and cable range type a : material of cord tube : metal, with cable dia. range of ( 5.7 to 6.5) b : material of cord tube : metal, with cable dia. range of ( 6.5 to 7.3) m : material of cord tube : plastic, with cable dia. range of ( 5.7 to 6.5) n : material of cord tube : plastic, with cable dia. range of ( 6.5 to 7.3) k : material of cord tube : metal, with cable dia. range of ( 8.0 to 9.0) b number of contacts : contacts available (2 or 10) c contact shape s : female contact for solder termination sc : female contact for crimping termination d other specifications : a two-digit character is added to indicate other specifications as needed. receptacle hr08d 12 wr - 10 p ( ** ) ^ _ ` a b c crimp contact hr34b - sc1 - 2 1 1 ^ _ ` a b ^ model name : hr08d series _ shell size : diameter (mm) of the mating interface of the plug ` shell type y wr receptacle a number of contacts : contacts available (10 only) b contact shape p : male contact for solder termination c other specifications : a two-digit character is added to indicate other specifications as needed. ^ model name : hr34b series (shares the same contacts as the hr34b series) _ contact type sc1 : female contact ` contact shape 1 : single contact 2 : reel contact a barrel shape : 1 : 20 to 25 awg b plating type 1 : gold plating 3 hr08d series small, waterproof, push-on bayonet lock connectors straight plug regular version ( cord tube material : plastic) robust version (cord tube material: metal) 8 10 47 13 20 a 49.1 (example) solder termination version part no. hrs no. a applicable cable diameter range (reference) contact solder cup inner diameter hr08d-12wpm-10s(31) 108-0274-5 31 7.4 5.7 to 6.5 1 hr08d-12wpn-10s(31) 108-0275-8 31 8.5 6.5 to 7.3 hr08d-12wpm-2s(31) 108-0272-0 31 7.4 5.7 to 6.5 1.8 hr08d-12wpn-2s(31) 108-0266-7 31 8.5 6.5 to 7.3 solder termination version part no. hrs no. a applicable cable diameter range (reference) contact solder cup inner diameter HR08D-12WPA-10S(31) 108-0219-7 31 7.4 5.7 to 6.5 1 hr08d-12wpb-10s(31) 108-0231-2 31 8.5 6.5 to 7.3 hr08d-12wpk-10s(31) 108-0262-6 31 9.5 8.0 to 9.0 hr08d-12wpa-2s(31) 108-0279-9 31 7.4 5.7 to 6.5 1.8 hr08d-12wpb-2s(31) 108-0280-8 31 8.5 6.5 to 7.3 hr08d-12wpk-2s(31) 108-0281-0 31 9.5 8.0 to 9.0 crimp termination version part no. hrs no. a applicable cable diameter range (reference) hr08d-12wpm-10sc(31) 108-0268-2 31 7.4 5.7 to 6.5 hr08d-12wpn-10sc(31) 108-0269-5 31 8.5 6.5 to 7.3 crimp termination version part no. hrs no. a applicable cable diameter range (reference) HR08D-12WPA-10Sc(31) 108-0220-6 31 7.4 5.7 to 6.5 hr08d-12wpb-10sc(31) 108-0232-5 31 8.5 6.5 to 7.3 hr08d-12wpk-10sc(31) 108-0263-9 31 9.5 8.0 to 9.0 4 hr08d series small, waterproof, push-on bayonet lock connectors right angle plug regular version ( cord tube material : plastic) robust version (cord tube material: metal) 10 8 7 4 13 20 33.5 ba ( exam p le ) solder termination version part no. hrs no. a b applicable cable diameter range (reference) contact solder cup inner diameter hr08d-12wlpm-10s(31) 108-0276-0 31 7.4 30.85 (5.7 to 6.5) 1 hr08d-12wlpn-10s(31) 108-0277-3 31 8.5 (6.5 to 7.3) hr08d-12wlpm-2s(31) 108-0273-2 31 7.4 (5.7 to 6.5) 1.8 hr08d-12wlpn-2s(31) 108-0267-0 31 8.5 (6.5 to 7.3) solder termination version part no. hrs no. a b applicable cable diameter range (reference) contact solder cup inner diameter hr08d-12wlpa-10s(31) 108-0221-9 31 7.4 30.5 (5.7 to 6.5) 1 hr08d-12wlpb-10s(31) 108-0233-8 31 8.5 (6.5 to 7.3) hr08d-12wlpk-10s(31) 108-0264-1 31 9.5 31.5 (8.0 to 9.0) hr08d-12wlpa-2s(31) 108-0282-3 31 7.4 30.5 (5.7 to 6.5) 1.8 hr08d-12wlpb-2s(31) 108-0283-6 31 8.5 (6.5 to 7.3) hr08d-12wlpk-2s(31) 108-0284-9 31 9.5 31.5 (8.0 to 9.0) crimp termination version part no. hrs no. a b applicable cable diameter range (reference) hr08d-12wlpm-10sc(31) 108-0270-4 31 7.4 30.85 (5.7 to 6.5) hr08d-12wlpn-10sc(31) 108-0271-7 31 8.5 (6.5 to 7.3) crimp termination version part no. hrs no. a b applicable cable diameter range (reference) hr08d-12wlpa-10sc(31) 108-0222-1 31 7.4 30.5 (5.7 to 6.5) hr08d-12wlpb-10sc(31) 108-0234-0 31 8.5 (6.5 to 7.3) hr08d-12wlpk-10sc(31) 108-0265-4 31 9.5 31.5 (8.0 to 9.0) 5 hr08d series small, waterproof, push-on bayonet lock connectors receptacle solder termination version b panel mount hole dimensions a b a b 4 (r2.8
4 3.2 a a c d e 4 part no. hrs no. a b contact solder cup inner diameter hr08d-12wr-10p(31) 108-0218-4 31 17.26 23.4 1.1 note : the number 10 contact is connected to the outer shell, which provides the ground connection. dimension hr08d-12wr-10p(31) a 17.26?.05 b m3?.5 c1 y 0/ ? 0.1 d 12.2 y +0.1/0 e 16.2 y +0.1/0 crimp contact female contact 1.2 15 type part no. hrs no. applicable electric wires loose piece contact hr34b-sc1-111 134-0051-7 20 to 25 awg reel contact hr34b-sc1-211 134-0050-4 note : the loose piece contacts are sold in packs of 100. reel contacts are sold in full reel quantities of 10,000 pieces per reel. 6 hr08d series small, waterproof, push-on bayonet lock connectors 2-6-3,nakagawa chuoh,tsuzuki-ku,yokohama-shi 224-8540,japan tel: + 81-45-620-3526 fax: + 81-45-591-3726 http://www.hirose.com http://www.hirose-connectors.com ? b applicable tools tools part no. hrs no. applicable contacts applicable wire size manual crimping tool ht304/hr34b-1 150-0107-9 hr34b-sc1-111 20 awg z 23 awg z 25 awg automatic crimping press cm-105c 901-0001-0 hr34b-sc1-211 20 to 25 awg automatic crimping applicator ap105-hr34b-1 901-2051-2 contact extraction tool rp6-sc-tp 150-0039-0 hr34b-sc1-111 hr34b-sc1-211 ---------------------- b manual crimping tool b operating precautions 1. prior to inserting or extracting this connector, make sure that the connector is not energized and the power is in the off posi tion. 2. there may be some resistance when inserting the cables into this connector, even if the cables are within the applicable cable range. this is to be expected due to the connector? waterproof ability. the waterproof performance and clamp force is dependant on t he cable specification. please check the cable specifications before using as they can cause a difference in performance in the waterpr oof protection and cable clamp force. 3. please contact your local hirose sales representative for any inquiries regarding the assembly procedures of this connector. b contact extraction tool b automatic crimping press cm-105c model (applicator sold separately) b plug contact diagram 2 position version 10 position version 1 2 321 7654 10 98 note : the numbering of the contact is from the plug termination side. the characteristics and the specifications contained herein are for reference purpose. please refer to the latest customer dra wings prior to use. the contents of this catalog are current as of date of 07/2018. contents are subject to change without notice for the purpose o f improvements.
sep.1.2018 copyright 2018 hirose electric co., ltd. all rights reserved. powered by tcpdf (www.tcpdf.org) 1 2018.7 ? small, waterproof, push-on bayonet lock connectors hr08d series features 1. simplified mating operations ? to mate the connector, simply push it onto the receptacle. to unmate, rotate the locking collar and pull the plug back from the receptacle. (fig. q ) ? simplified mating is enabled by the alignment markings ? mating guide keys are provided at 3 points to prevent contact damage. they also provide the ability to blind mate these connectors when needed. plug connector does not damage the receptacle contacts. 2. waterproof structure supports ip67 and ip68 ratings while in the mated condition. (ratings explained below*) *ip67: submerged in 1 m for 30 minutes *ip68: submerged in 2 m for 14 days 3. adjustable cable direction the right angle plug can be adjusted to mount in any of the 8 different directions (adjustable in 45 increments). (fig. w ) 4. variations available fig. q fig. w items no. of contacts 2 or 10 positions available connector type straight plug, right angle plug, receptacle (10 pos. only) plug termination crimp, solder receptacle termination solder cord tube material plastic, metal cable diameter range (reference) 5.7 to 6.5 6.5 to 7.3 8.0 to 9.0 cable exit directions push-on bayonet lock mating is completed simply by pushing the plug onto the receptacle. to unmate this connector, rotate the locking collar to release the lock, then pull them apart. in cases where the application will demand a high level of reliability, such as automotive, please contact a company representative for further information. 2 hr08d series small, waterproof, push-on bayonet lock connectors product speci cations ratings rated current 3a operating temperature range -20? to +85? rated voltage ac200v, dc250v storage temperature range -10? to +60? items speci cations conditions 1. contact resistance 20m?or below measured with dc 1a 2.insulation resistance minimum of 1,000m measured with dc 500v 3. withstanding voltage no ashover or breakdown 10 pos. ac 900v for 1 minute 2 pos. ac 1,500v for 1 minute 4. vibration resistance no electrical discontinuity of 10? or greater tested in 3 directions with 10 to 500hz /cycle, total vibration width of 0.75mm, and 98m/s 2 , 3 hours each. 5. shock no electrical discontinuity of 10? or greater tested in 3 directions with the acceleration of 490m/s 2 , and a duration of 11ms, 3 times each 6. durability contact resistance : maximum of 30m 500 mating cycles 7. temperature cycles insulation resistance : minimum of 500m left at - 55? : 30 minutes e ordinary temperature : 2 to 3 minutes e 85? : 30 minutes e ordinary temperature : 2 to 3 minutes, 2 to 3 minutes, total of 5 cycles 8. humidity resistance insulation resistance minimum of 50m (high humidity) minimum of 500m (dry) left at temperature 71? and humidity 95% for 336 hours. left at the temperature of 71? and 95% humidity for 336 hours. 9. waterproof structure should be no water leakage inside the connector left submerged in water at the depth of 1m, for 0.5 hours, in the mated condition. materials / finish plug component materials finish remarks outer shell zinc alloy, aluminum alloy and polyamide resin (black) nickel under plating ---------------------- insulator pps resin (black) ---------------------- ul94v-0 female contact phosphorous bronze gold plating ---------------------- o ring, gasket nbr, nitrile hydride rubber ---------------------- ---------------------- receptacle component materials finish remarks outer shell zinc alloy nickel under plating ---------------------- insulator pps resin (black) ---------------------- ul94v-0 male contact 10 position brass gold plating ---------------------- o ring nbr ---------------------- ---------------------- product number structure refer to the chart below when determining the product specifications from the product number. please select from the product numbers listed in this catalog when placing orders. plug hr08d 12 wp a - 10 s ( ** ) ^ _ ` a b c d ^ model name : hr08d series _ shell size : diameter (mm) of the mating interface of the plug ` shell type wp : straight plug, wlp: right angle plug a cord tube and cable range type a : material of cord tube : metal, with cable dia. range of ( 5.7 to 6.5) b : material of cord tube : metal, with cable dia. range of ( 6.5 to 7.3) m : material of cord tube : plastic, with cable dia. range of ( 5.7 to 6.5) n : material of cord tube : plastic, with cable dia. range of ( 6.5 to 7.3) k : material of cord tube : metal, with cable dia. range of ( 8.0 to 9.0) b number of contacts : contacts available (2 or 10) c contact shape s : female contact for solder termination sc : female contact for crimping termination d other specifications : a two-digit character is added to indicate other specifications as needed. receptacle hr08d 12 wr - 10 p ( ** ) ^ _ ` a b c crimp contact hr34b - sc1 - 2 1 1 ^ _ ` a b ^ model name : hr08d series _ shell size : diameter (mm) of the mating interface of the plug ` shell type y wr receptacle a number of contacts : contacts available (10 only) b contact shape p : male contact for solder termination c other specifications : a two-digit character is added to indicate other specifications as needed. ^ model name : hr34b series (shares the same contacts as the hr34b series) _ contact type sc1 : female contact ` contact shape 1 : single contact 2 : reel contact a barrel shape : 1 : 20 to 25 awg b plating type 1 : gold plating 3 hr08d series small, waterproof, push-on bayonet lock connectors straight plug regular version ( cord tube material : plastic) robust version (cord tube material: metal) 8 10 47 13 20 a 49.1 (example) solder termination version part no. hrs no. a applicable cable diameter range (reference) contact solder cup inner diameter hr08d-12wpm-10s(31) 108-0274-5 31 7.4 5.7 to 6.5 1 hr08d-12wpn-10s(31) 108-0275-8 31 8.5 6.5 to 7.3 hr08d-12wpm-2s(31) 108-0272-0 31 7.4 5.7 to 6.5 1.8 hr08d-12wpn-2s(31) 108-0266-7 31 8.5 6.5 to 7.3 solder termination version part no. hrs no. a applicable cable diameter range (reference) contact solder cup inner diameter HR08D-12WPA-10S(31) 108-0219-7 31 7.4 5.7 to 6.5 1 hr08d-12wpb-10s(31) 108-0231-2 31 8.5 6.5 to 7.3 hr08d-12wpk-10s(31) 108-0262-6 31 9.5 8.0 to 9.0 hr08d-12wpa-2s(31) 108-0279-9 31 7.4 5.7 to 6.5 1.8 hr08d-12wpb-2s(31) 108-0280-8 31 8.5 6.5 to 7.3 hr08d-12wpk-2s(31) 108-0281-0 31 9.5 8.0 to 9.0 crimp termination version part no. hrs no. a applicable cable diameter range (reference) hr08d-12wpm-10sc(31) 108-0268-2 31 7.4 5.7 to 6.5 hr08d-12wpn-10sc(31) 108-0269-5 31 8.5 6.5 to 7.3 crimp termination version part no. hrs no. a applicable cable diameter range (reference) HR08D-12WPA-10Sc(31) 108-0220-6 31 7.4 5.7 to 6.5 hr08d-12wpb-10sc(31) 108-0232-5 31 8.5 6.5 to 7.3 hr08d-12wpk-10sc(31) 108-0263-9 31 9.5 8.0 to 9.0 4 hr08d series small, waterproof, push-on bayonet lock connectors right angle plug regular version ( cord tube material : plastic) robust version (cord tube material: metal) 10 8 7 4 13 20 33.5 ba ( exam p le ) solder termination version part no. hrs no. a b applicable cable diameter range (reference) contact solder cup inner diameter hr08d-12wlpm-10s(31) 108-0276-0 31 7.4 30.85 (5.7 to 6.5) 1 hr08d-12wlpn-10s(31) 108-0277-3 31 8.5 (6.5 to 7.3) hr08d-12wlpm-2s(31) 108-0273-2 31 7.4 (5.7 to 6.5) 1.8 hr08d-12wlpn-2s(31) 108-0267-0 31 8.5 (6.5 to 7.3) solder termination version part no. hrs no. a b applicable cable diameter range (reference) contact solder cup inner diameter hr08d-12wlpa-10s(31) 108-0221-9 31 7.4 30.5 (5.7 to 6.5) 1 hr08d-12wlpb-10s(31) 108-0233-8 31 8.5 (6.5 to 7.3) hr08d-12wlpk-10s(31) 108-0264-1 31 9.5 31.5 (8.0 to 9.0) hr08d-12wlpa-2s(31) 108-0282-3 31 7.4 30.5 (5.7 to 6.5) 1.8 hr08d-12wlpb-2s(31) 108-0283-6 31 8.5 (6.5 to 7.3) hr08d-12wlpk-2s(31) 108-0284-9 31 9.5 31.5 (8.0 to 9.0) crimp termination version part no. hrs no. a b applicable cable diameter range (reference) hr08d-12wlpm-10sc(31) 108-0270-4 31 7.4 30.85 (5.7 to 6.5) hr08d-12wlpn-10sc(31) 108-0271-7 31 8.5 (6.5 to 7.3) crimp termination version part no. hrs no. a b applicable cable diameter range (reference) hr08d-12wlpa-10sc(31) 108-0222-1 31 7.4 30.5 (5.7 to 6.5) hr08d-12wlpb-10sc(31) 108-0234-0 31 8.5 (6.5 to 7.3) hr08d-12wlpk-10sc(31) 108-0265-4 31 9.5 31.5 (8.0 to 9.0) 5 hr08d series small, waterproof, push-on bayonet lock connectors receptacle solder termination version b panel mount hole dimensions a b a b 4 (r2.8
4 3.2 a a c d e 4 part no. hrs no. a b contact solder cup inner diameter hr08d-12wr-10p(31) 108-0218-4 31 17.26 23.4 1.1 note : the number 10 contact is connected to the outer shell, which provides the ground connection. dimension hr08d-12wr-10p(31) a 17.26?.05 b m3?.5 c1 y 0/ ? 0.1 d 12.2 y +0.1/0 e 16.2 y +0.1/0 crimp contact female contact 1.2 15 type part no. hrs no. applicable electric wires loose piece contact hr34b-sc1-111 134-0051-7 20 to 25 awg reel contact hr34b-sc1-211 134-0050-4 note : the loose piece contacts are sold in packs of 100. reel contacts are sold in full reel quantities of 10,000 pieces per reel. 6 hr08d series small, waterproof, push-on bayonet lock connectors 2-6-3,nakagawa chuoh,tsuzuki-ku,yokohama-shi 224-8540,japan tel: + 81-45-620-3526 fax: + 81-45-591-3726 http://www.hirose.com http://www.hirose-connectors.com ? b applicable tools tools part no. hrs no. applicable contacts applicable wire size manual crimping tool ht304/hr34b-1 150-0107-9 hr34b-sc1-111 20 awg z 23 awg z 25 awg automatic crimping press cm-105c 901-0001-0 hr34b-sc1-211 20 to 25 awg automatic crimping applicator ap105-hr34b-1 901-2051-2 contact extraction tool rp6-sc-tp 150-0039-0 hr34b-sc1-111 hr34b-sc1-211 ---------------------- b manual crimping tool b operating precautions 1. prior to inserting or extracting this connector, make sure that the connector is not energized and the power is in the off posi tion. 2. there may be some resistance when inserting the cables into this connector, even if the cables are within the applicable cable range. this is to be expected due to the connector? waterproof ability. the waterproof performance and clamp force is dependant on t he cable specification. please check the cable specifications before using as they can cause a difference in performance in the waterpr oof protection and cable clamp force. 3. please contact your local hirose sales representative for any inquiries regarding the assembly procedures of this connector. b contact extraction tool b automatic crimping press cm-105c model (applicator sold separately) b plug contact diagram 2 position version 10 position version 1 2 321 7654 10 98 note : the numbering of the contact is from the plug termination side. the characteristics and the specifications contained herein are for reference purpose. please refer to the latest customer dra wings prior to use. the contents of this catalog are current as of date of 07/2018. contents are subject to change without notice for the purpose o f improvements.

▲Up To Search▲

Price & Availability of HR08D-12WPA-10S

	To Download HR08D-12WPA-10S Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .